Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

Inspecting XPS before it is covered: a site handover guide

XPS insulation

At a glance

Inspect XPS immediately before concreting, backfilling or fitting a lining hides it. Identify the boards, then check thickness, support, joints and continuity at thresholds, plinths and service penetrations. Inspect waterproofing separately: well-laid XPS is not evidence of a watertight membrane. On the inspection record, mark the areas checked and when any repairs must be reinspected. The next crew then knows which areas can be covered and which must stay accessible.

Light cream XPS boards with smooth surfaces and straight edges

Identify the XPS actually installed

Photograph the batch label and check the grade, thickness, edge, thermal and mechanical properties against the design. Even one manufacturer can supply similar-looking boards for different uses. For a substitution, attach its product documentation and record who approved it.

Check thickness and continuity

Measure representative areas and awkward details. Check the thickness for each zone and, in multi-layer work, verify that all layers are present. Look beneath cut pieces that might hide a gap in a lower layer.

Trace the connection to adjacent insulation on the drawing, especially at floor edges, plinths and thresholds. A sound main area cannot compensate for a break at a junction. Take an overview and close-ups with a scale and identifiable location.

Check bearing and flatness

Boards should not rock or rest on isolated high spots. Bearing must match the design, particularly on a floor requiring a level, stable base. Do not rely on the weight of a later screed to correct irregularities.

XPS is not a levelling compound. Voids and damaged pieces change how pressure is transferred. Use the agreed access route to inspect unstable areas, including around services where cut pieces often replace full boards.

Examine joints and corners

Check that rebates actually overlap without a step. Butt joints need straight cuts and close contact. A broken corner is still a defect even where it will be hidden by the finish.

Before covering, replace a poorly cut piece or correct the layout in accordance with the detail. Use the specified joint treatment. Filling a gap with an arbitrary mortar can introduce an unnecessary heat path.

Inspect the waterproofing separately

XPS may protect waterproofing, but it cannot establish that the coating is continuous. Inspect seams, junctions and penetrations separately before backfilling the perimeter. A leak will be harder to reach afterwards.

On walls check board fixing and substrate condition. Pressure water can call for a different arrangement from ground moisture. Confirm adhesive compatibility, look for unintended punctures and record any specified separation layer next to a membrane.

Protect the work during the next operation

Reinforcement work and foot traffic can damage boards before concreting; backfill brings soil pressure and sharp debris against walls. Include the protection arrangements in the handover so the work is not damaged immediately after inspection.

Agree storage areas, access routes and edge protection. Lightweight boards are easy to handle but still need an organised site. Avoid incompatible chemicals, excessive sun and heat sources, and follow the instructions for the materials used.

Record defects and their correction

Record the area, date, XPS type and findings. Locate photographs on a plan or simple sketch. If a defect is found, verify and record the repair before the work is closed; a note alone does not correct it.

This check gives the contractor a clear repair list and the owner useful records. With agreed criteria the inspection need not take long. Its value lies in the timing: inspect what is about to disappear beneath concrete, soil or a finish.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide