Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

When is T35 trapezoidal steel sheet a good choice for a roof?

Roof coverings

At a glance

Consider T35 trapezoidal steel sheet where a deeper rib is useful and the product’s load table suits the support spacing on the roof. To compare it with T18, obtain both cross-section drawings, steel thicknesses and figures for the same span arrangement. For repairs, the side lap matters just as much: a new sheet with the same profile name may not fit the existing one. This guide explains what to check in the documentation before ordering and how to use effective cover to estimate the cost of the whole slope.

Graphite-coloured T35 trapezoidal steel sheet showing the rib profile

What distinguishes the T35 profile?

T35 profiles have ribs around 35 mm high that stiffen the sheet and give the slope a pronounced pattern. For the actual product, also check rib spacing, the position and shape of stiffeners and effective cover width. These dimensions let you draw the true covered strip.

When replacing a sheet, compare the old and new cross-sections, particularly the edge shapes that form the side lap. Identify the weather face and the roofing version of the product. Turning the sheet over can change drainage at the joint.

When might T35 have an advantage over T18?

A deeper profile can increase section stiffness. In the product table, select the row for the steel grade and thickness, span arrangement, bearing width and deflection criterion. Compare it with the design loads to establish whether the support spacing is suitable.

For a garage roof, compare two complete options: T35 on the proposed supports and T18 on a layout sized for that product. Ask the designer to assess both and obtain a price for both supports and covering. Compare samples as well, since taller ribs give a more pronounced roof surface.

What do sheet thickness and coating change?

For two quotations, list steel thickness, sheet weight and coating system separately. Thickness affects structural behaviour and weight. Choose the metallic protection and paint for the environment and finish required. Ask for the precise designation of each variant.

Describe conditions on both sides of the roof. Outside, salt or industrial deposits may affect the sheet. Inside, humidity and condensation may matter more. Match the reverse coating to the interior. Moisture removal and ventilation belong in the design of the whole assembly.

How do pitch and sheet length affect the choice?

Read the pitch section in the model’s instructions and check whether it uses percentages or degrees. Also check the requirements for end laps, seals and underlay. A pitch quoted for a continuous sheet may have different conditions from one for a slope with an end lap.

Measure the ordered length between the designed eaves and ridge terminations. Confirm it on site, taking the sheet projection and space for flashings into account. Agree transport and lifting arrangements for long sheets to avoid kinking the profile during handling.

How does T35 affect the roofing budget?

Balex Metal’s catalogue of 28 October 2026 listed BTD35 roofing sheet in PE25 polyester at about €9.01 per m² of effective cover for 0.50 mm steel and €13.75 for 0.70 mm, excluding VAT. The original prices of PLN 39.73 and PLN 60.63 use the NBP rate that day of PLN 4.4090 per euro. Labour, delivery and flashings are separate.

Prepare a list of whole sheets allowing for cuts and laps. Add supports, fixings, ridge and eaves details. If a supplier assumes fewer supports, include that saving only once calculations for the revised layout have confirmed it.

What information should go in the order?

Mark the pitch, support spacings and proposed roof equipment on the order drawing. Specify the model, weather face, cover width, coating and colour. For solar panels, agree with the designer which part of the structure will take the loads from the array fixings.

On delivery, read the pack labels and inspect the edges that will form the laps. Report a damaged lap edge before installation. Store the sheets as instructed and keep the ordered profile drawing for future repair or extension work.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide