Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

Buying PIR boards: how to spot an incomplete insulation quote

PIR insulation

At a glance

Ask what will be finished when the crew leaves. A square metre of PIR does not include substrate preparation, fixings or sealed junctions unless the quote says so. Boards that look alike can differ in facing, strength and intended use. Before ordering, obtain the current technical data sheet, declaration of performance and installation instructions for the exact variant. Name it on the order and match it to the pack labels before the delivery is split between rooms. Then compare the cost of two complete installations, not the price of boards delivered to the kerb against a finished job.

Cross-section of a factory-made PIR board showing thickness, facing and edge for delivery inspection

Link the documents to the delivered variant

Check thickness, edge profile and board type. Resolve discrepancies before installation. Keep a label photograph and delivery note so the concealed layer can still be identified later.

Compare equivalent scopes

Compare declared resistance at the offered thickness and the facing’s connection to the next layer in separate columns. Equal thickness does not guarantee equal resistance; equal conductivity does not prove adhesive compatibility. Mark supply-only and installed prices.

List preparation, boards, accessories, labour, waste disposal and site protection. Then check whether a lower total represents a saving or a missing service. Both proposals should leave the house with the same specified result.

Board size and access

Check pack dimensions against the narrowest doorway and stair turn. Large sheets cover an open area quickly but corners are vulnerable on a tight staircase. Smaller boards may be easier despite the higher piece count.

Walk the route from lorry to installation point and identify a dry storage area. Easy loading onto the truck does not imply easy handling inside; excessive stock can obstruct the work.

Cutting plan and edge joints

Lay out full boards along the longest straight run before marking recesses, returns and openings. At every cut check whether the tongue, groove, lap or straight edge remaining will mate with the next board.

A rectangular area and a room with alcoves need different allowances. Retain usable offcuts for identified positions, but do not build critical details from assorted scraps merely to reduce waste.

Who supplies tapes, adhesive and fixings?

For each tape, adhesive or fixing, note the surfaces it joins and who selects it. Taping a facing, bonding a substrate and anchoring into structure require different compatibility checks.

If the owner buys boards and the installer buys accessories, agree on the combination before work. Record who supplies each item so an incompatible component is not improvised after the layer is concealed.

Costs and handover

Schedule inspection of substrate, boards and connections before concealment. Price protection, cutting and accessories too. Agree these steps before payment so acceptance covers installation and not just the number of packs.

Use location-labelled photographs rather than unidentifiable close-ups. At handover, ask for a record of the completed build-up. It will be more useful during repairs than a material invoice alone.

Worked example: checking quantities

For 90 m², a 1,200 × 600 mm board covers a nominal 0.72 m², giving a geometric minimum of 125. At 2,400 × 1,200 mm the nominal area is 2.88 m²: just over 31 boards, hence at least 32 whole boards. These figures omit edge profiles, effective coverage, cuts and waste. Order from the layout and list joint foam separately; it is an accessory, not a replacement for boards.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide