Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

Insulating a room with termPIR AL GK: what to check before renovation

PIR insulation

At a glance

When the exterior cannot change, termPIR AL GK combines rigid PIR insulation with a 12.5 mm plasterboard lining on the room side. The PIR layer has gas-tight facings on both sides. The composite can simplify installation, but the new gypsum surface will hide the old wall. Establish why the room feels cold, whether the masonry is damp and how corners and reveals will behave after insulation. Measure the space lost to the entire panel, not just its core. Also plan sockets, cupboard fixings and the route for bringing long boards into the room.

termPIR AL GK insulation board showing its PIR core and facing

Start with the existing wall

Before choosing the composite, describe the masonry, its condition, room use and reveal clearance. The plasterboard provides a finishing surface but will hide moisture behind it.

Measure the route from unloading point to room, especially stair turns. An unplanned cut creates another joint to finish. Mark sockets and future fittings on the wall and agree a cutting plan before delivery.

Check handling and layout together

An AL GK panel is 2,600 mm long and 1,200 mm wide. At a suitable room height it can cover much of a wall without a horizontal joint, provided it can be carried in and turned upright.

Sketch the wall with doors and cable outlets. Before cutting a board for a tight corridor, check where the new seam will fall once installed. Agree panel lengths, cuts and handling space.

Separate core and panel thickness

The figure of 0.022 W/(m·K) describes the PIR part, not the foam and gypsum together. Divide the core’s own thickness by that conductivity when estimating its resistance.

Use total panel thickness when checking room width. For thermal assessment separate the PIR and 12.5 mm plasterboard or use the correct declared R. Using the whole dimension with the PIR lambda would exaggerate the benefit.

What happens to moisture in the masonry?

Internal insulation reduces heat supplied to the masonry. The colder wall may dry differently; covering it with plasterboard does not remove a moisture source.

Inspect the ceiling junction and any moisture marks. Establish their cause and the future drying path before enclosing the wall. Keep a condition record to distinguish pre-existing defects from later damage.

Fire classification and heavy fixings

Read B-s1,d0 within the specified end-use conditions for AL GK. It neither makes the core non-combustible nor gives the lining’s permissible load.

For a wall cabinet, mark the bracket and the substrate that will carry it behind the lining. Design the fixing through the full load path, not merely into the plasterboard. Keep the service drawing and fire classification separately.

Define a paint-ready finish

Request both core and overall composite thickness in the quote. Include installation materials, joint treatment and perimeter closures as well as panels.

Compare the paint-ready wall made with composite panels against separate layers. Include wall preparation, cuts at sockets, fixing and finishing all junctions in both. Bonding a board does not automatically include these tasks.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide