Even picket spacing: setting out a fence bay without cumulative errors
Metal fence pickets and fencing
Set out the entire bay before fastening the first metal picket. Measure the clear infill width, choose the margins at both posts and check whether brackets or other fittings restrict access there. Then choose a whole number of pickets and work out the internal gaps. Mark positions from one fixed point. If you set every new picket only by its neighbour, a small error can repeat along the row and leave an unexpectedly narrow gap at the last post. A spacer is useful, but the position of the last picket should already be on your sketch.

Set out both ends first
In an asymmetrical bay, avoid hiding the difference in progressively smaller gaps. Decide where an unequal margin makes sense, or straighten the supporting frame first. The repetitive edges of profiled steel pickets make deviations easy to see.
Distinguish clear gap from pitch
The clear gap is the empty space between edges; pitch includes one picket and one gap. A 115 mm profile with a 25 mm gap has a pitch of 140 mm. This illustrates the distinction and is not a universal spacing recommendation.
Use one marking convention throughout. Switching between an edge and a centre line introduces mistakes. Note on the sketch what each mark on the rail represents so everyone sets out the same way.
Mark check points from a common datum
Measure each position from one fixed point rather than moving the tape to the previous mark each time. Cross-check a few marks near the middle of the bay. This catches a discrepancy before the entire row is attached.
Check picket position at every support level; rails may not run exactly parallel. Accurate marks on just one rail do not keep a picket vertical. Even a slight difference between top and bottom shows up on a long picket.
Use a spacer as a local check
Choose an accurately sized spacer with a surface that will not scratch the coating. It should slide between pickets without force. If it stops fitting, find out why rather than bending the pickets apart.
A spacer checks only the immediate gap, not the width already used. After several pickets, compare their positions with the datum marks. Combining the two checks is more reliable than relying on either alone.
Check the width of the delivered profiles
Inspect several pickets for actual width and distorted ends. Manufacturing tolerances can affect alignment. Do not squeeze or spread every profile to force it to match an assumed dimension.
Keep the shape intended by the manufacturer. Resolve substantial differences from the documentation with the supplier. Forcing pickets into shape can damage the coating and alter stiffness; use measured dimensions for setting out.
Control the top and bottom lines
Equal gaps do not correct uneven picket heights. Establish a top level or the intended curve. A sloping site needs its own reference line; do not follow every small ground irregularity with the bottom edge.
A temporary guide batten can aid alignment if it will not damage the pickets. It is not a permanent support. Remove temporary aids after assembly, inspect the finished joints and view the bay from the usual approach.
Keep the picket still while fastening
A thin section can move as a screw is tightened. Hold it in position and check the vertical and clear gap before making the final connection as instructed. Adjust the tool and pressure to avoid deforming the fixing point.
For a two-person crew, agree who checks alignment and who makes the connection. Inspect the first few pickets before repeating the method. A repeatable technique is useful only once it has been tried on the actual materials.
Use the last gap to check the whole layout
Measure the space left before fixing the final pieces. If it differs significantly from the sketch, stop and trace the error. Cutting the last picket lengthwise as a quick fix changes its cross-section and finish. An even fence comes from setting out the full width.
Compare the measurements of apparently identical bays before reusing a template. Unless their widths match, the final margin can differ even when every internal gap has been maintained accurately.
Free quote
What to include in your enquiry
Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.
More from the building guide
Before laying metal fence slats horizontally, check that the manufacturer permits that orientation. Turning a vertical picket on its side changes its…
Replacing the infill can change the appearance of a fence without rebuilding it from scratch, provided the existing supports are suitable. Metal…
A fence on sloping ground needs more than a single height dimension. Draw its upper and lower edges before ordering: stepped bays…
To calculate how many vertical metal pickets fit in a single row, allow for the clear gaps and both end margins as…
Plan a metal-picket fence around everyday use of the property: visibility at the gate, garden privacy and pedestrian access. Picket width, gaps…
Uneven gaps, rust-coloured spots and a loose picket can have quite different causes. Before tightening, grinding or straightening anything, examine the layout,…
Inspect a finished metal picket fence from both sides against the agreed specification. Start with the profile, lengths, end shapes, colour and…
Assess a metal picket fence as a complete arrangement of posts, rails and infill. The pickets determine colour, rhythm and screening, but…




















