Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

Parapet copings: tracing water stains and ripples in the metal

Sheet metal flashings

At a glance

A stain down the façade, a lifting corner and a rippled coping can point to different faults. Before specifying replacement metal, inspect the supports, fixings, joints and layers beneath the coping. Water can enter through a lap, at an incorrectly formed end or through damaged waterproofing. It may travel before it leaves a mark on the render. Start the inspection on top of the parapet and on its roof side. Pay particular attention to corners, where sections running in different directions meet. The new coping detail will depend on which fault the inspection uncovers.

Parapet coping with a shaped side and drip edges

Trace stains back from the façade

Record when damp appears and whether it coincides with strong wind. An apparently closed joint can have a gap underneath. Conversely, a badly formed edge can wash dirt down the façade while the wall itself remains dry. Inspect the junction to distinguish the two.

Investigate support and movement where metal ripples

Wide sheet reveals uneven support and thermal movement. Rigid fixings in several places can restrain expansion and distort the coping. Before adding more fasteners, examine the section joints and the movement the detail is intended to allow.

A handling dent differs from a series of deformations following the supports. Establish the cause before replacing the sheet. If the support remains uneven the new coping may develop the same pattern. Assess the installation conditions before specifying the expected flatness.

Check the fall and drip edge

The parapet top should shed water in the direction shown on the drawings. Low spots hold water and deposits. Side folds protect the edges and a formed drip helps water break clear of the façade. Check whether a drip flattened during earlier work can be restored to its intended shape.

Increasing the overhang changes how the section and its fixings behave. Size a bespoke coping to the finished wall width, including its outer layers. Measure at several points because the width of an older parapet can vary along its length.

Inspect the waterproofing beneath the coping

The coping works with the waterproofing at the roof and wall. On removal, inspect the continuity of that layer, its upstands and joints. Fitting new metal over a torn membrane can leave the source of the leak in place.

Examine the frame and the material the fixings engage. Damp or weakened supports need attention before the coping goes back. Photograph the exposed layers to document repairs that will be concealed when the external metalwork is inspected at handover.

Product overview: Made-to-measure flashings from SteelProfil

Match the sheet to the junction and façade

Galvanised, aluminium-zinc coated and colour-coated sheet have different protective layers. Check compatibility at points of contact with adjacent materials and suitability for the local exposure before comparing the colour with the old finish.

Gloss and texture differences stand out along a long parapet. Compare a sample at the building alongside any ridge caps, verge flashings and gutter aprons that are to match. Starter strips and chimney flashings still need fixings chosen for their own functions.

Inspect corners and terminations at handover

Inspect section joints, corners and ends against adjoining walls. Check the fall and look for standing water. Before sealing a visible joint, establish how it accommodates movement and where water is supposed to leave it.

Remove swarf and protective film as specified for the sheet. Record the sealants and surface repair products used. At subsequent inspections look at both the metal and the wall below. A change in the stain pattern can reveal a developing drainage fault.

Questions and answers

Do ripples always mean the sheet is defective?

No. The support, handling damage, restraints or thermal movement can produce distortion. Assess the metal in its installed condition.

Will a new coping repair damaged waterproofing?

Inspect and repair the waterproofing once it is exposed. The metal coping is one part of the roof and wall junction.

Can screws be added through the top face?

Only where the specified fixing detail permits it. An unplanned penetration can admit water or restrain thermal movement.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide