Choose a material

Roofing sheets

Blachy trapezowe

Sandwich panels

Płyty warstwowe

PIR insulation boards

Płyty izolacyjne PIR

XPS

Izolacja XPS

Accessories

Akcesoria montażowe

Fencing

Sztachety metalowe

Short of space for insulation? Assessing termPIR MAX 19 AL

PIR insulation

At a glance

A low threshold or an existing eaves flashing can limit insulation depth. termPIR MAX 19 AL combines a rigid PIR core with gas-tight facings of aluminium, paper and polyethylene. Its low conductivity can reduce the thickness needed to meet a given layer resistance. The useful question is whether that saving lets you retain the threshold or flashing. Draw the finished section with each proposed board, allowing for support, adjoining layers and fixings. If both options fit without rebuilding, compare the remaining requirements and the full installed price before paying a premium.

termPIR MAX 19 AL insulation board showing its PIR core and facing

Identify the detail that needs the space

Measure the depth below the flashing after deducting every layer except insulation. Identify what would need rebuilding if the board did not fit. Low conductivity changes thickness, not substrate condition or the flashing junction.

Ask for two dimensioned sections rather than two totals. If neither requires a change to the existing opening or flashing, compare cost, load suitability and installation details on their merits.

What to look for at a joint

On a MAX 19 AL sample, TAG denotes a tongue-and-groove joint, LAP a shiplap and FIT a square edge. Match the sample to the ordered designation.

Trial-fit two boards over the uneven area. If the joint closes only under pressure, inspect flatness and support rather than forcing it. Record edge condition and any residual gap before covering.

Translate the thermal target into a stock size

The declared λD of 0.019 W/(m·K) for MAX 19 AL applies from 80 to 220 mm. Respect that range even when a preliminary calculation produces an unusual thickness.

For R = 5.0 m²K/W, 5.0 × 0.019 gives 0.095 m, or 95 mm. This is a calculation, not a guarantee of a 95 mm stock size. Choose an available thickness that meets the target, verify its declared resistance and recalculate the complete assembly.

Protect boards and vapour-control junctions

Provide dry storage and temporary protection before delivery. The gas-tight face resists vapour across the laminate; it does not provide a factory seal between adjacent boards.

At a perimeter penetration, show how the facing meets the wall seal. Inspect it before covering and protect the open edge overnight. A lambda of 0.019 cannot stop air passing through an open joint.

Check compression and fire separately

This variant declares CS(10/Y)100 and reaction-to-fire class E. Do not substitute CS120 from a different silver-faced board.

Check the required thermal resistance, equipment loads and fire requirements independently. Saving space at the threshold addresses the first. Keep the exact variant’s documentation and the assembly assessment for the others.

Compare the cost of keeping the existing geometry

Compare 600 × 1,200 and 1,200 × 2,400 mm layouts. Adjust nominal area for the edge profile and compare prices at the same thermal target.

Separate alteration of the threshold or flashing, fixings and finishes in both estimates. The difference in the finished detail shows whether the higher board price avoids other costs. Include effective coverage and cuts for both layouts.

7 branches. Materials closer to your project.

  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]
Budowlanka.org — map

Free quote

What to include in your enquiry

Tell us how you plan to use the material, the dimensions and the quantity you need. Include the thickness, grade or variant name, along with the delivery town or your preferred collection branch. For a specific product, add its name or a link to the product page. We will reply to the email address you provide to discuss availability and the terms of your order.

More from the building guide